TILTFORGE

Fit checker

Will TiltForge fit your blinds?

TiltForge mounts inside the headrail of a horizontal blind, and needs the standard 2-inch-tall headrail. A photo of the headrail end with something of known size in frame is enough for an estimate, and a couple of angles is better than one.

1 · How do your blinds tilt?

2 · Photo of the headrail

Lay a US quarter flat inside the headrail, then photograph it at an angle from above — tipped down into the channel, not straight down at it — with the tilt rod in the same frame. Up to 4 angles of the same rail.

How to shoot it — one photo, three things in it

One shot does the whole job: angle down into the open rail, quarter lying flat inside, tilt rod in frame. Everything below is that one photo, explained.

1 · Angle into the rail, don't shoot straight down

Tip the camera down into the channel until you can see both the floor of the rail and the inside of its far wall. That lands nearer overhead than side-on — about 60 degrees from level. Too shallow and you are sighting along the rail's own diagonal, with nothing visible inside it; straight down and the wall is gone.

Angled down into the channelThe wall stands up in the frame, so its height can be measured.
Flat, straight down at the railThe wall collapses to a line and the height is simply not in the photo.

Straight down is the natural way to photograph a rail on a bench, and it is the one shot that cannot work. Looking down, the only width you can measure runs across the channel — that is the rail's depth, and depth is 57 mm on both profiles, so it cannot tell them apart.

2 · Lay the quarter flat inside the rail

Just drop it in. Lying flat in the bottom of the rail is enough — no holding, no tape. Propped flat against one of the inside walls works just as well if that is easier. Either way it only has to be inside the rail and clearly in shot.

Lying in the bottomThe easiest one. Just drop it in.
Flat against an inside wallWorks equally well — taped, or just held there.
Outside the rail, on the sillA different plane from the rail, so its scale doesn't carry over.

A quarter is 24.26 mm across, and seen at an angle a circle projects as an ellipse. How squashed that ellipse is gives away how steeply you shot, so the coin sets the scale and the angle in one go and the rail's height can be corrected rather than guessed. Which surface it is lying on changes the sum slightly, not what you have to do — we work that out from the picture. A tape measure or ruler laid in the rail does the same job. What does not work is a coin outside the rail, on the sill or the bench: it is in a different plane from the thing being measured, so its scale doesn't carry over.

3 · Get the tilt rod in the same frame

The thin rod running the length of the channel. Keep it in shot alongside the quarter, and we can read how high it sits above the floor of the rail.

Rod and quarter togetherWe can read the rod's height off the same scale.
Rod cropped out of frameStill answers the fit question, but not the rod one.

TiltRod is modeled around a rod sitting 35 mm above the inside floor of the rail. It doesn't change the fit verdict — a 51 mm rail is still a 51 mm rail — but if yours sits well off that, better to find out now than with the part in your hand. Miss the rod and you still get an answer on the headrail.

Send up to four angles of the same rail if you like. The first is the anchor and the rest cross-check it, which is worth doing — two views that agree are a firmer answer than one. And keep the light behind you: a rail shot into the window is a silhouette, and a silhouette measures 38 mm as easily as 51.

What we're measuring

Pull the blind away from the wall and look at the open end of the headrail. The dimension that decides fit is the height — the short side, top edge to bottom edge.

2 in51 mm2.25 in / 57 mm
46 mm or taller
Fits — high-profile rail
43–45 mm
Between the two — send a squarer photo
42 mm or shorter
Low-profile — doesn't fit yet

Depth is 2.25 in (57 mm) on both profiles, so it isn't what decides — don't measure that one. The two profiles are 13 mm apart in height, so a tape that lands within a few millimeters of either one has already answered the question.

The tilt rod

The photo can't see what shape your tilt rod is, so check that with calipers across the flats. The kit has inserts for:

  • D (one flat) 6.35 mm (1/4") × 4.76 mm (3/16")
  • Hex 6.35 mm (1/4")
  • Hex 5.56 mm (7/32")
  • Square 5.72 mm

Rod not on the list? Print your own adapter →

This is an estimate — measure to confirm, using the height above. Your photos are sent to the vision model for the check and are not stored.